![]() If PPP is not enabled, dial in to the RSC modem. To use this option, PPP must be enabled.ĭ. If you are already connected to your company Ethernet, use the telnet command to connect to RSC.Ĭ. Note that, unlike the graphical user interface, the command-line interface does not attempt to connect to RSC by appending -rsc to the name you enter if that name fails.ī. Use point-to-point protocol (PPP) to connect to your company Ethernet, and then use the telnet command to connect to RSC.Īsk your network administrator if you do not know the server's RSC name (Sun recommends the name servername- rsc). See userperm username for information about user permission levels.Īfter RSC software is installed and configured and an account has been set up for you, you can connect to RSC and log in to your account using a Solaris workstation, Microsoft Windows PC, standard ASCII character terminal, or a computer running ASCII terminal emulation software.įollow these steps to log in to your RSC account:ġ.Ĝonnect to RSC using one of these methods:Ī. Note - Some commands require a specific user permission level. More detailed descriptions of the commands are provided in the following sections. Note - For Sun Enterprise 250 servers, the following shell command aliases are not available: showenvironment, showdate, setdate, and showsc. Show the state of the system locator LED (Sun Fire V480 servers only). Turn the system locator LED on or off (Sun Fire V480 servers only). Shows characteristics of an RSC user accountĭisplays a list of RSC shell commands and a brief description of eachĭisplays version number for RSC firmware and componentsĭisplays information stored in the RSC serial EEPROM Makes the current boot and run console logs "original"ĭisplays one or more configuration variablesĭisplays or sets the current time and date ![]() Generates an externally initiated soft reset to the serverĬontrols server firmware behavior, if followed by a server reset within 10 minutes (similar to L1-key combinations on non-USB Sun keyboards)ĭisplays the history of all events logged in the RSC event bufferĭisplays the history of all console messages logged in the buffer ĭisplays current environmental informationĭisplays the current network configuration Each command is explained in greater detail in the following sections. The following table summarizes RSC shell commands. This chapter tells you how to log in to your RSC account and describes RSC command use and syntax. Note - Sun Enterprise 250 servers support two concurrent telnet sessions and three active concurrent RSC GUI sessions.Īfter you log in to your RSC account, the RSC shell prompt appears ( rsc>), and you can enter RSC shell commands. In addition, RSC supports up to four active concurrent RSC GUI sessions. RSC supports a total of four concurrent telnet sessions per server, including command-line interface sessions and a graphical user interface (GUI) connection to the server console (Open Console). ![]() It also has commands for configuring RSC. The RSC command shell is a simple command-line interface that supports commands that allow you to administer or diagnose the server. Var Projectile = Java.type('. Remote System Control (RSC) 2.2 User's Guide Var AbstractNPC = Java.type('.npc.AbstractNPC') Var CombatStyle = Java.type('.combat.CombatStyle') Var MeleeAttackHandler = Java.extend(Java.type('.')) We want this to be as close to perfect as we can get it, we want feedback thats the point in the live version of the server so we have get all the feedback from you.Ĭode: var AttackHandler = Java.type('.') Expect to see quests soon because we have about 10-12 Quests completed once we are done with the implementing the system. We have spent a lot of time on it and plan to spend a lot more time on it until its perfect. Yes ZRS3 is a hosted server while in development the live version will receives updates multiple times a day, you may see some stuff on the thread that is not done in the live version yet.Īn all around great server starting with a good exp rate and drop rate to stabilize the economy, The combat is going to be the main focus to accomplish mini-games influence PvP. ZRS3 is built of a heavily modified version of virtue, it is a 835 witch in the new few weeks we will be loading the current RS cache, ZRS3 will be a remake of RuneScape 3 with shortcuts, faster exp but with all of the same content. ZRS3 is a a project a few others and i have been working on for a month or so, our main focus was combat and now we have a great base for that we want to show it off a little more and go more in-depth about the project.
0 Comments
Leave a Reply. |